MCKARLEN VIETNAM · ENGINEERING SOLUTIONS

Wastewater and Drainage

Classify liquid, solids, sump, inflow and installation conditions before selecting suitable submersible or drainage pump equipment.

01 · APPLICATION CONTEXT

Application and system context

01

Industrial wastewater

Review liquid composition and solids by model.

02

Sumps

Review usable volume, switching levels and pump count.

03

Site drainage

Assess rainwater, mud/sand and portable installation conditions.

04

Large-volume drainage

Consider BL only within source-supported drainage contexts and by model.

02 · ENGINEERING CHALLENGES

Common engineering challenges

01

Undefined solids

Size, fibrous content, density and clogging risk are unknown.

02

Incomplete sump data

Dimensions, levels, inflow and pumping cycle are missing.

03

Static head only

Pipe, valve, elevation and discharge losses are omitted.

04

Harsh liquid

Corrosion, abrasion, temperature and chemicals require material review.

03 · REQUIRED PROJECT DATA

Required project data

Liquid Source, composition, temperature, pH when known, solids and material needs.
Hydraulics Inflow, required flow, elevations, piping and discharge point.
Sump / installation Sump dimensions, levels, guide-rail/portable arrangement and maintenance access.
Electrical / controls Supply, pump count, alternation, level alarms and protection.

04 · ENGINEERING APPROACH

Review and selection flow

  1. Classify the liquid, solids and application conditions.
  2. Establish inflow, sump volume and duty point.
  3. Review solids passage, materials and impeller type by model.
  4. Compare ACI, HDP, GV and KT; use BL only in source-supported contexts.
  5. Confirm installation, controls, documents and maintenance boundary.

05 · PRODUCT ROLE

Relevant product families

ACI for industrial wastewater; HDP/GV for model-controlled wastewater and drainage; KT for dewatering; BL for source-supported large-volume drainage contexts. No combined family-wide performance range is stated.

CONTROLLED FAMILY

ACI

Use only after duty, liquid, model and configuration are confirmed.

CONTROLLED FAMILY

HDP

Use only after duty, liquid, model and configuration are confirmed.

CONTROLLED FAMILY

GV

Use only after duty, liquid, model and configuration are confirmed.

CONTROLLED FAMILY

KT

Use only after duty, liquid, model and configuration are confirmed.

CONTROLLED FAMILY

BL

Use only after duty, liquid, model and configuration are confirmed.

SELECT BY APPLICATION

Sewage pumping and high-volume drainage

Select by liquid conditions and duty point, not just motor power or flow.

ACI · Sewage sumps and pump replacement

The catalogue identifies ACI as a submersible sewage pump family, with flexible-pipe, rigid-pipe or automatic coupling installation depending on configuration. Replacement requires checks of the liquid, solid size, duty point and installation compatibility.

BL / KL · High-volume drainage

BL and KL are catalogue families of high-volume axial / mixed-flow submersible pumps for applications such as drainage, irrigation and aquaculture. For liquids containing sand, solids or fibrous debris, confirm the limits of the individual model. High flow alone does not establish suitability for every type of wastewater.

Data to provide

Site and existing pump nameplate photos, liquid composition, required flow, total head, pipe diameter and length, power supply, water levels and installation arrangement.

Floodwater drainage for workshops and basements

Start with the inflow source, collection point and discharge location. Select against the liquid, flow at total head and installation conditions.

When should the site be assessed?

Water enters the workshop or basement ramp; the sump rises while the pump runs; pumps clog or flow falls; existing equipment needs replacement or standby pumping.

Information to prepare

Photographs of inflow, sump and pump nameplate; sump dimensions and water levels; solids or debris; discharge point, elevation difference, pipe length and diameter; power supply. Add design flow, total head and drawings where available.

Configuration principles

Review inflow and collection first, then the pump, discharge pipe, backflow prevention and level control. Consider standby pumping, high-level alarms and power according to the project. Discharge onto the street is not a default solution.

Select against the liquid

Distinguish floodwater, sand-laden water and sewage. KT is grouped under construction dewatering in the technical documentation; ACI is a submersible sewage pump family; BL/KL address high-volume duties. Sand, fibres, oil or chemicals require individual model-limit checks. Do not substitute by motor power alone.

Drainage depends on inflow, discharge water level, piping losses and power. A catalogue does not demonstrate flood protection for the whole property. Design, installation and acceptance remain subject to agreed project responsibilities.

Is the largest maximum flow enough?

No. Check flow at the required total head on the performance curve.

The pump runs but water rises?

Check inflow, actual duty point, blockages, discharge water level and system condition.

Can a clean-water pump drain floodwater?

Only where the liquid and operating conditions are within model limits. Check solids, debris and fibres first.

06 · RESPONSIBILITY CONTROL

Selection and responsibility boundaries

McKarlen scope

  • Review liquid, sump and duty data
  • Recommend family/model within controlled evidence
  • Provide model-controlled technical documents when available

Responsible-party scope

  • Universal non-clogging guarantees
  • Complete wastewater-system or civil-sump design
  • Household-pump positioning or invented project cases

07 · DOCUMENT CONTROL

Technical documents and evidence

  • Reviewed Pump Schedule / BOQAvailable
  • Correct model curveRequest by model
  • Model-specific dimensional drawingRequest by model
  • Datasheet and material confirmationRequest by model

Document-use principle

Release only the confirmed family, model and revision. Legacy catalogues or documents with obsolete identity are not converted into public downloads.

08 · EVIDENCE GATE

Project evidence

No project record currently meets the evidence and usage-right threshold for publication on this page. No Project Case card is created until that evidence exists.

09 · KNOWLEDGE

Engineering knowledge / FAQ

Can pipe diameter alone determine the pump?

No. Flow, head, liquid, solids, sump and operating pattern are needed.

Can one family handle every wastewater type?

No. Liquid, solids and materials must be confirmed by model.

Is BL classified as a wastewater pump?

It should not be. The source supports specific drainage and other named contexts only.

Can a project case be published now?

Only with sufficient evidence, usage rights and approved wording.

10 · VIETNAM SUPPORT

Technical support in Vietnam

Support covers data intake, duty review, model selection, technical documents, spare parts, warranty and after-sales within the supplied-equipment scope.

Project-data review
Model / configuration selection
Documents and after-sales support

11 · PROJECT ENQUIRY

Prepare a technical enquiry

ApplicationFlowHead / pressureLiquidDocuments

Submit technical enquiry