HDP Series

HDP pumps are the ultimate choice for high head pumps designed for continuous, unattended operation. Over the years, they have proven their reliable performance in a wide range of challenging applications worldwide. HDP drain pumps are designed for professional use in harsh applications such as excavation, drainage, irrigation, light industry, commercial and residential and other industries.

Category: ,

01 · WASTEWATER / DRAINAGE SUBMERSIBLE PUMP

HDP Series

Submersible wastewater and drainage pumps with a non-clogging vortex impeller. The model is confirmed against flow, head, liquid characteristics, solids size, sump depth and operating conditions.

FlowHeadWastewaterSolidsSump
View Model-controlled DataSubmit Pump Selection Data
McKarlen HDP Series wastewater submersible pump
HDP SeriesWastewater / drainage submersible pump
HDP Series pump sectional drawing extracted from the controlled technical source
HDP SeriesProduct sectional drawing

02 · TYPE AND SERIES POSITION

A submersible pump family for drainage duties with soft solids

HDP is selected against the duty point, wastewater, solids, sump depth and discharge arrangement. The product image identifies the family and does not assign an unconfirmed exact model.

HDP Series submersible pump
HDP SERIES

Wastewater and drainage submersible pump

The non-clogging vortex impeller provides a flow passage for wastewater containing soft solids within the selected model’s limit.

  • Submerged operation in a sump or collection area
  • Selected against flow and total head
  • Solids and sump conditions reviewed
HDP Series sectional drawing
MODEL CONTROL

Seven models in the technical source

HDP-05, HDP-10, HDP-20, HDP-30, HDP-50, HDP-75 and HDP-100 retain separate model-table data.

  • No one specification is applied to every model
  • Curves are issued by selected model
  • Materials retain component-level scope

03 · EQUIPMENT APPLICATIONS

Application contexts requiring actual operating data

These are equipment application contexts. They do not state that McKarlen designs or executes the complete system.

Industrial Drainage

Review the wastewater source, solids, temperature and operating schedule.

Sumps and Collection Areas

Select against inflow, water levels, total head and useful sump volume.

Construction-site Dewatering

Use as drainage equipment where the liquid and solids suit the selected model.

Water Intake and Transfer

Confirm liquid conditions, intake screen, discharge route and submergence depth.

Replacement Duties

Compare the duty point, connection, electrical supply and installation conditions.

04 · KEY TECHNICAL DATA

Technical data is controlled by model and curve

The old catalogue’s aggregate flow, head, power and connection summaries do not align with its model table. The preview therefore does not present one common whole-series range.

HDP Series — stable technical field order

Model curve1. Flow
By model2. Head
By model3. Power
2900 / 34504. rpm · 50/60 Hz
MODEL DATA

Model relationships retained

Model order: HDP-05, 10, 20, 30, 50, 75, 100.

5. Connection — HDP-05: 1¼ in / 38 mm; other models confirmed against the model table
6. Liquid — wastewater / drainage with soft solids
7. Liquid temperature — 0–40°C
8. Pressure — Confirm by model.
Solids passage — 12 or 15 mm by model
Maximum submergence depth — 6 m
Recorded model data: power 0.4 / 0.75 / 1.5 / 2.2 / 3.7 / 5.5 / 7.5 kW; head, connection, dimensions and weight remain attached to the corresponding model row.
Rated current: Confirm by model.

05 · PERFORMANCE AND DUTY

Flow and head must be reviewed on the selected model curve

HDP cannot be selected from pipe diameter or static lift alone. Curve revision, frequency and wastewater conditions must be reviewed together.

Duty point + wastewater + solids

Total head includes static lift and pipe losses at the design flow. Model selection also reviews operating mode and sump conditions.

Duty PointFlow and total head
WastewaterSource, temperature and characteristics
SolidsSize, form and blockage risk
OperationContinuous, intermittent and standby duty
Responsibility boundary: McKarlen supports equipment selection and product-data confirmation. Sump design, piping, electrical work, construction, installation and site acceptance remain with the relevant project parties.

06 · MATERIALS AND CONFIGURATION

9. Materials — confirm by component and selected model

A material assigned to one component is not presented as a material grade for the complete pump.

HDP material table by component
MATERIAL SOURCE

Component-controlled material table

The source table is presented in the materials section. Values are read by component and confirmed against the selected model.

  • No material is assigned to the complete pump
  • No transfer to another family or model
  • Confirm against the model record before supply
CONTROLLED STRUCTURE

Component · Material · Applicability

Pump casing — Cast iron — confirm by model
Impeller — Ductile cast iron — HDP vortex impeller
Motor housing — Stainless steel 304 — source configuration
Shaft — Stainless steel 304 — source configuration
Pump-side seal — SiC/ALOX — component-specific
Motor-side seal — CAR/ALOX — component-specific
O-ring / packing — NBR — component-specific

07 · INSTALLATION CONDITIONS

10. Installation conditions — prepare for submerged operation and pump removal

McKarlen provides equipment-related guidance. Sump and system design and site execution remain with the responsible project parties.

Depth and Water LevelsConfirm sump depth, start/stop levels and the 6 m maximum submergence limit.
Solids and Intake ScreenReview solids size and form and the risk of screen or impeller blockage.
Discharge and ConnectionConfirm model connection, pipe losses and removal requirements.
Electrical Supply and ProtectionConfirm 50/60 Hz, the actual electrical supply, motor protection and control mode.

08 · TECHNICAL DOCUMENTS

HDP documents are issued by model and purpose

The 2020 catalogue is used as an internal technical source but is not approved for public download because it contains obsolete corporate identity.

Controlled Document

The PDF carrying superseded corporate identity is not linked directly.

HDP Technical CatalogueRequest a controlled copy; old edition not released

Request Documents

Request by Model

Provide a model or duty point to receive the correct document.

Pump CurveBy model, frequency and duty point

Request Pump Curve

Technical DrawingBy model and installation conditions

Request Technical Drawing

Datasheet and MaterialsConfirmed by model

Request Technical Documents

10 · SPARE PARTS, WARRANTY AND AFTER-SALES

Support based on model, equipment information and operating conditions

Provide equipment photos, nameplate information, delivery records, wastewater data and observed condition for review.

Model-specific Spare Parts

Identify parts from the model, configuration, equipment details and photos of the required component.

Warranty Intake

Review delivery records, operating conditions and actual inspection findings.

After-sales Technical Support

Equipment-related guidance, operating-data review and product-document support.

Sump design, piping, electrical supply, installation and operating issues are assessed separately before support or warranty scope is confirmed.

11 · MODEL SELECTION

Submit wastewater data and the duty point for HDP selection

The technical team will review the inputs, identify missing information and discuss the model, configuration and required documents.

FlowHeadWastewater / solidsSumpDrawing / BOQ
Submit Pump Selection DataContact Technical Support

❄